Two Tank CIP Washers

More Information

Cylindrical CIP Tank Standard Common Features:

• 304/316 SS Sanitary Construction with #4 or 2B Finish.
  NOTE: 50 to 300 Gal. Tanks Built of 14 Ga. Stainless; 400 through 1,200 Gal. Tanks Built of 10 or 12 Ga. Stainless.
• Legs: All tubular stainless steel 18” Height, suitably cross-tied with adjustable feet, located to permit piping in front of, or under, tank.
  NOTE: 50-150 Gallon Tanks use 1 ½” Tubular Legs, 200-400 Gallon with 2″ Tube Legs and 500-1,200 with either 2″ or 2 ½” Schedule 40 Stainless Pipe Legs.
• Covers: Flanged, All-welded, with 18″ Manhole manway cover with hinge.
• Anti-Vortex Bottom.
• Inlet and Outlet Fittings: Standard Tri-Clamp inlet and Tri-Clamp outlet, please specify sizes for inlet/outlet clamp connection and fittings.
• Overflow: Skimmer top large diameter stainless steel tube.
  NOTE: Overflow Size is 3″ for 50 through 400 Gal. Tanks and 4″ for 500-1,200 Gal. Tanks.
• Bridge: Full flanged top welded to sidewall with 18” manway to provide ample space for all pipe fittings and alignment.
• Sidewalls: Cylindrical for strength.
• Corners: Formed to radius for sanitation.
• Drain: Bottom formed for drainage with anti-vortex drain faced vertical or horizontal for piping choice
• Capacity: To fit the need. Varied capacity tanks can be aligned with uniform height for appearance. Combine two or more CIP tanks to make wash water/chemical re-use systems and skids.
• All outside welds ground and polished. Specify cover, polish and inlet/outlet size requirements on orders. Reach out to us for specialty custom sizing outside of those shown here, we’ll be happy to help/quote on custom.
• Spray Ball: Standard and included, please specify size.

Available with these finishes:
Glass shot blast Finishing
No. 4 Finish with all welds ground and polished;
No. 4 Finish Outside welds ground and polished, Inside Blasted;
No. 2B Finish, Outside welds ground and polished, Inside Blasted
No. 2B Finish, Finish All Welds Blasted

Pictured Above: Safgard Multi Tank Two Tank with Eductor System

Series CIP-C Cylindrical Tank Models / Part Numbers:
(Combine multiple tanks below together to create multi-tank CIP systems.)

Cylindrical CIP Tanks
Gallon	Diameter	Height	Part Number
50	23"	32"	32712
100	27"	48"	32713
150	31"	48"	32714
195	34.5	48	32717
200	38.5"	48"	32715
240	38.5	48	32718
250	38.5"	60"	32716
300	46"	48"	32719
345	46	48	32720
400	46"	60"	32733
430	46	60	32721
500	52"	60"	32734
520	50	60	32722
600	58"	60"	32735
620	55	60	32723
800	65"	60"	32736
1000	73"	60"	32737
1200	81"	60"	32738

Rectangular CIP Tanks
Gallon	Diameter	Height	Part Number
160	30"	40"	32725
210	30"	52"	32726
230	36"	40"	32727
300	36"	52"	32728
280	40"	40"	32729
375	40"	52"	32730
400	48"	40"	32731
525	48"	52"	32732

Optional Heating Concepts:

• In-tank heating (steam heat assembly)
  Three (3) automated magnetrol assemblies, with ¾” solenoid steam valves, piping, mixer, and thermowell in each CIP tank sidewall

OR

• Shell and Tube Heating Assembly (return condensate or boiler) (steam trap by others)
  B.G. S.U. 85-2, 2 pass, 80-100 GPM, 24 SS T./Bundle, inlet/outlet, 3 x 2 tri-clamp reducer, 4″ flange plate, Gasket, bolts with 1.5″ welded couplings
• Steam Valve
  Electric, magnetrol 1 ¼” S.V. with Thermostat
• Thermowell Holder
  3″ x 2″ Tri-Clamp, 5 Port (or RTD assembly)

CIP Tanks Additional Features to Consider:

• P.H. Port – 2″ installed in sidewall – detergent tank
• Additional Tri-clamp top of tank ports
  3″ tri-clamp
  2 ½” Tri-clamp
  2″ tri-clamp
• Suction Manifold: Piping, clamps, 2 (¼), ½ couplings with two (2) 2 ½” air valves
  Optional: with (2) 2 ½” Air Actuated Butterfly Valves
• Return Line Manifold – Piping clamps, recorder bulb tee, Two (2) 2″ air diverter valve
  Optional: with two (2) 2.5″ air actuated butterfly valves
• Stainless steel tubular base: for pump and motor
• CIP Pump and Motor: Includes clamps, fittings, and installation
  7 ½ – 10 H.P. Options, 3-Phase, 3500 RPM, TEFC.
• Water Assembly (1 per tank)
  (2) anti-siphon device, 1 ¼” NPT, welded to top of tank
  (2) 1 ¼” Asco water solenoid valve, liquid level control, 3 probes, tri-clamp cap, Q-clamp
  (1) Tube SS ¼” x 15″ welded through above tri-clamp cap (alkali feed supply to Detg. Tank)
• Thermowell parts
  for high temperature cut off
• Anti-Siphon Water Inlet
  With or without solenoid valve
• Liquid Level Controls and fittings
• Valves and piping
• Stainless Steel Cabinet for Master Controls
  Type 304 Stainless. Specify wall or unit mounting. Hinged/Locking Door and cutouts. (Dimensions: 36″ W x 42″ H x 12″ Diam.)
  (Optional: Add sub-panel if master panel is remote, to house air pack, liquid level control, and temperature components. (Dimensions: 20″ W x 30″ H x 10″ Diam. With cover fasteners)
• CIP Recorder – Installed (With Delay to Temperature Switch)
  Mechanical: Anderson 80-180 Deg. Range, temperature only, 1-Pen
  Anderson 80-120 Deg range 2-pen, with sanitary isolating transducer and pressure
  Anderson 80-180 Deg. Range 2-Pen, temperature and pressure (no isolating transducer)
  Anderson 80-180 Deg. Range 1-Pen, temperature only (with RTD Assembly)
• Solid State
  Anderson 2-Pen, temperature only (with RTD assembly)
  Anderson 2-Pen, temperature and pressure, sanitary pressure transducer
• Air Blow with Ball Check Valve Assembly – 2″ TC
  Includes air solenoid valve, regulator, including installation of hose and quick disconnect.

Accessories for Two-Tank CIP Systems:

• SB-1 Spray Ball – 40 GPM or 80 GPM
• TS-4 Transport 40′ drop-in spray
• Balancer – Spring Tension (For TS-4 Tanker Spray Device)
• Carrier (For TS-4 Tanker Spray Device)
• Rail – 4″ I-beam/hanger/prime coated
• Turns- 90 Degree/48 Degree Radius Bend/prime coated
• Motorized ¼ HP Chain Foil – 500 Lbs.
• 20′ CIP hose with Stainless Steel Fittings,2 ½” three fly heavy-duty rubber
• 20′ CIP hose with Stainless Steel Fittings, 2″ three fly heavy-duty rubber