Three Tank CIP Washers

More Information

Cylindrical CIP Tank Standard Common Features:

• 304/316 SS Sanitary Construction with #4 or 2B Finish.
  NOTE: 50 to 300 Gal. Tanks Built of 14 Ga. Stainless; 400 through 1,200 Gal. Tanks Built of 10″ or 12″ Ga. Stainless. *(We have just 12 now)
• Legs: All tubular stainless steel 18” Height, suitably cross-tied with adjustable feet, located to permit piping in front of, or under, tank.
  NOTE: 50-150 Gallon Tanks use 1 ½” Tubular Legs, 200-400 Gallon with 2″ Tube Legs and 500-1,200 with either 2″ or 2 ½” Schedule 40 Stainless Pipe Legs.
• Covers: Flanged, All-welded, with 18″ Manhole manway cover with hinge.
• Anti-Vortex Bottom.
• Inlet and Outlet Fittings: Standard Tri-Clamp inlet and Tri-Clamp outlet, please specify sizes for inlet/outlet clamp connection and fittings.
• Overflow: Skimmer top large diameter stainless steel tube.
  NOTE: Overflow Size is 3″ for 50 through 400 Gal. Tanks and 4″ for 500-1,200 Gal. Tanks.
• Bridge: Full flanged top welded to sidewall with 18” manway to provide ample space for all pipe fittings and alignment.
• Sidewalls: Cylindrical for strength.
• Corners: Formed to radius for sanitation.
• Drain: Bottom formed for drainage with anti-vortex drain faced vertical or horizontal for piping choice
• Capacity: To fit the need. Varied capacity tanks can be aligned with uniform height for appearance. Combine two or more CIP tanks to make wash water/chemical re-use systems and skids.
• All outside welds ground and polished. Specify cover, polish and inlet/outlet size requirements on orders. Reach out to us for specialty custom sizing outside of those shown here, we’ll be happy to help/quote on custom.
• Spray Ball: Standard and included, please specify size.

Glass shot blast Finishing, but also Available with these finishes:
No. 4 Finish with all welds ground and polished;
No. 4 Finish Outside welds ground and polished, Inside Blasted;
No. 2B Finish, Outside welds ground and polished, Inside Blasted
No. 2B Finish, Finish All Welds Blasted

Optional Heating Concepts:

• In-tank heating (steam heat assembly)
• Three (3) automated magnetrol assemblies, with ¾” solenoid steam valves, piping, mixer, and thermowell in each CIP tank sidewall

OR

• Shell and Tube Heating Assembly (return condensate or boiler) (steam trap by others)
• B.G. S.U. 85-2, 2 pass, 80-100 GPM, 24 SS T./Bundle, inlet/outlet, 3 x 2 tri-clamp reducer, 4″ flange plate, Gasket, bolts with 1.5″ welded couplings
• Steam Valve
  Electric, magnetrol 1 ¼” S.V. with Thermostat
• Thermowell Holder
  3″ x 2″ Tri-Clamp, 5 Port (or RTD assembly)

Cylindrical CIP Tank Models / Part Numbers:
*Combine to create multi-tank CIP systems:

CIP Tanks Additional Features to Consider:

• P.H. Port – 2″ installed in sidewall – detergent tank
• Additional Tri-clamp top of tank ports
  3″ tri-clamp
  2 ½” Tri-clamp
  2″ tri-clamp
• Suction Manifold: Piping, clamps, 2(¼), ½ couplings with three (3) 2 ½” air valves
  Optional: with (3) 2 ½” Air Actuated Butterfly Valves
• Return Line Manifold –Piping clamps, recorder bulb tee, (3) 2″ air diverter valve
  Optional: with (4) 2.5″ air actuated butterfly valves
• Stainless steel tubular base: for pump and motor
• CIP Pump and Motor: Includes clamps, fittings, and installation
  7 ½ – 10 H.P. Options, 3-Phase, 3500 RPM, TEFC.
• Water Assembly (1 per tank)
  (3) of anti-siphon device, 1 ¼” NPT, welded to top of tank
  (3) of 1 ¼” Asco water solenoid valve, liquid level control, 3 probes, tri-clamp cap, Q-clamp
  (1) SS Tubes ¼” x 15″ welded through above tri-clamp cap, alkali feed supply to detg. Tank
• Thermowell parts
  for high temperature cut off
• Anti-Siphon Water Inlet
  With or without solenoid valve
• Liquid Level Controls and fittings
• Valves and piping
• Stainless Steel Cabinet for Master Controls
  Type 304 Stainless. Specify wall or unit mounting. Hinged/Locking Door and cutouts. (Dimensions: 36″ W x 42″ H x 12″ Diam.)
  (Optional: Add sub-panel if master panel is remote, to house air pack, liquid level control, and temperature components. (Dimensions: 20″ W x 30″ H x 10″ Diam. With cover fasteners)
• CIP Recorder – Installed (With Delay to Temperature Switch)
  Mechanical: Anderson 80-180 Deg. Range, temperature only, 1-Pen
  Anderson 80-120 Deg range 2-pen, with sanitary isolating transducer and pressure
  Anderson 80-180 Deg. Range 2-Pen, temperature and pressure (no isolating transducer)
  Anderson 80-180 Deg. Range 1-Pen, temperature only (with RTD Assembly
• Solid State
  Anderson 2-Pen, temperature only (with RTD assembly)
  Anderson 2-Pen, temperature and pressure, sanitary pressure transducer
• Air Blow with Ball Check Valve Assembly – 2″ TC
  Includes air solenoid valve, regulator, including installation of hose and quick disconnect.

Multi-Tank System Accessories:

• SB-1 Spray Ball – 40 GPM or 80 GPM
• TS-4 Transport 40′ drop-in spray
• Balancer – Spring Tension (For TS-4 Tanker Spray Device)
• Carrier (For TS-4 Tanker Spray Device)
• Rail – 4″ I-beam/hanger/prime coated
• Turns- 90 Degree/48 Degree Radius Bend/prime coated
• Motorized ¼ HP Chain Foil – 500 Lbs.
• 20′ CIP hose with Stainless Steel Fittings,2 ½” three fly heavy-duty rubber
• 20′ CIP hose with Stainless Steel Fittings, 2″ three fly heavy-duty rubber